Set the corresponding reference point for measurements with the extension pin by pushing button The extension pin 14 swivels back in again by pushing it toward the housing to the stop. When a defect is determined, only the symbol shown aside flashes in the display. Veuillez lire et comprendre toutes les consignes. No apunte nunca la luz hacia otra persona o hacia otro objeto que no sea la pieza de trabajo.
This manual is also suitable for: Dlrk. Print page 1 Print document 33 pages. Rename the bookmark. Do not use the laser viewing glasses as sun glasses or in traffic. The laser viewing glasses do not afford complete UV protection and reduce color perception. The rangefinder is intended for measuring distances, lengths, heights, clearances and for calculating areas and volumes.
The rangefinder is suitable for interior and exterior construction site measuring. The numbering of the product features shown refers to the illustration of the digital laser rangefinder on the graphic pages. A The working range increases depending on how well the laser light is reflected from the surface of the target scattered, not reflective.
In unfavorable conditions. Please observe the article number on the type plate of your rangefinder. The trade names of the individual rangefinders may vary. The rangefinder can be clearly identified with the serial number 18 on the type plate. Fewer measurements are possible when using 1.
To open the battery lid 17 , press the latch of the battery lid 16 in the direction of the arrow and remove the battery lid. Insert the supplied batteries. When inserting, pay attention to the correct polarity according to the representation on the inside of the battery compartment. When the battery symbol appears in the display for the first time, then at least measurements are still possible.
The batteries must be replaced when the battery symbol. Always replace all batteries at the same time. Only use batteries from one brand and with the identical capacity. When storing for extended periods, the batteries can corrode and discharge themselves. Feed string loop on end of hand strap 25 under hand strap mounting post 26 and pull out on other side.
Feed hand strap 25 through string loop end and pull tight. When switching on the rangefinder, the laser beam is not switched on yet. To save the batteries, the rangefinder switches off automatically after approx. When a measured value has been stored, it is retained in automatic switch-off mode.
The rangefinder offers a variety of different measuring modes that can be selected by. After switching on, the rear edge of the rangefinder is preset as the reference point.
Upon selection of the measuring mode and the reference point, all further steps are carried out by pushing the measuring button 9.
With the reference point selected, place the rangefinder against the desired measuring line e. Push the measuring button 9 to switch on the laser beam. Do not point the laser beam! Aim the laser beam at the target surface. Push the measuring button 9 again to initiate the measurement. In the continuous measurement mode and continuous laser beam mode, the measurement already starts upon first actuation of the measuring button 9. The measured value appears after 0. The duration of the measurement depends on the distance, the light conditions and the reflection properties of the target surface.
Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over manuxl phone in a minute or two. Many instructions, immediately after the purchase, go into the trash gosch with the box, which is a mistake. If looking through the Bosch Power Tools DLR user manual directly on this website is not convenient for you, there are two possible solutions:.
Below you will find previews of the content of the user manuals presented on the following pages to Bosch Power Tools DLR Information concerning additional parts included in the set and optional By looking through this part of the document, you will be able to verify whether your Bosch DLR has been delivered to you with a full set of accessories.
Type the 4 letters New code. Your answer needs to include more details to help people. If something bad happens while using a Bosch DLR, you will have a set of documents that are required to obtain warranty repairs. Use the instructions of the Bosch DLR manufacturer to run the product properly, without unnecessary risk of damage to the equipment. It is good to get acquainted with it to avoid disappointments resulting from a shorter exploitation time of the product Bosch DLR than expected.
Some offer free download, others do not. However, if you cannot be convinced to collect manuals at your home, our website elr provide you with help. Helpful 0 Not Helpful Comment Flag. Here is a link to the manual online janual PDF format: Please enter a valid email address. The DLR rangefinder is ideal for measuring distance with some sort of backstop aka a wall or side of a hill or building. It would be difficult to measure a board for cutting or plotting out an area of land to put a foundation.
Unless you have someone to hold something at the desired point of measure for the laser to hit. That limitation not withstanding, this compact, lightweight, highly accurate rangefinder will be a great benefit to many future construction projects.
I have an earlier model of this and it works very well and is highly accurate. Makes measuring rooms, etc. I am thinking of getting this for my dad for Fathers Day. My dad is a pretty skilled at-home handy man, fixing things from bathrooms to molding to shelving to gardening beds to plumbing to…you name it. Replacing my tape measure was one of the best decisions i have ever made!
0コメント